Questions, answered
Everything an owner asks before saying yes.
Setup, your data, pricing, material intake, Jarvis: what it takes to turn your factory into an agent. No jargon, no fine print. We set it up for you.
The things owners ask first
Twenty-five honest answers.
Will it disrupt my machines or production?
No. Setup is non-invasive and takes minutes per machine: no rewiring, no modification, no downtime. A small sensor sits on the outside of the machine, so nothing about how the machine runs changes.
What actually goes on the machine?
A small box, on the outside of the machine. Nothing is opened, drilled or rewired. It takes its power from an ordinary plug point, so there is no battery for anyone to remember to change, and it needs a WiFi signal that reaches the machine. That is the whole installation.
There are two kinds, which is what lets us cover every machine on your floor rather than only the modern ones: one counts the machine's own pulses, and one works the output out from a formula you type in yourself. Both land on the same screen, each labelled with where it came from.
What happens when the power or the internet goes?
Nothing is lost and nothing is recorded twice. The sensor keeps its readings on the box and lets go of them only once the server confirms it has them, so a dropped connection costs you nothing: the readings arrive when the line comes back. A restart is not read as a repeat.
A machine that stopped while the line was down still shows as stopped from the time it actually stopped, not from the time the connection returned. And if the power to the machine itself goes, the machine is not running, which is exactly what you see: a stoppage, timed from when it began.
How long until it's live?
A pilot on a few machines is live the same day. Most factories have their products, materials and shifts fully configured within a few days, and from then on it just runs.
Do operators have to enter any data?
No. Output is measured at the machine instead of written on a sheet at the end of a shift, so your operators carry on exactly as they do today, and you have the figure while the shift is still running, not the morning after.
In the office the typing turns into checking. You tell Blitz once, with us, at setup, what goes into a product and what your month costs to run. From then on a supplier bill is photographed at the gate and read for you, and someone approves what was read; if a machine ran the wrong item, someone restamps that window; if a price is missing, someone supplies it.
That is minutes a day instead of evenings, and it is the kind of work that catches a mistake rather than the kind that copies one forward.
What happens when a number is missing?
Blitz tells you exactly which price it is waiting for, by name. And the minute you supply it, every figure that depended on it is right, back through the month.
When we rebuilt the costing on our own floor we found 31 products whose thread had no price. The old system costed every one of them at zero, which was a quiet way of saying they were free to make. Blitz names the gap instead, so closing it is a five-minute job rather than a wrong figure you quote from for a year. A machine nobody has measured for power is named and left out, not averaged in.
A zero says it was free. A blank tells you which price to go and get, and that is a number you can fix today.
Where does my data live, and is it secure?
Blitz is hosted and managed for you: no server to buy, nothing to maintain. Your data belongs to you: export it whenever you like, and we never sell or share it.
Who inside my factory can see my margins?
Only the people you give them to. Everyone works under their own login rather than a shared one, and what each person can open is set per person: the supervisor who needs the machine screen does not get your cost and profit pages along with it. We set that up with you when the office goes live, and you change it yourself afterwards.
The other half of the answer is that nobody can quietly rewrite yesterday. A sensor row is never edited. A correction is recorded against it, so the original and the change both stay on the record.
Do I need my own server or an IT team?
No. We host, secure and update Blitz for you: nothing to install, nobody to hire, and you can see your floor live from anywhere (the office, home or the road). Your office internet is enough for that.
The sensors need WiFi that reaches the machines and a power point at each one. We walk the floor before we quote and put in whatever coverage your machines need, so that is our job, not yours.
Does Blitz replace my accounting software?
No. It makes the one you have better fed. Blitz sends your accounting software clean entries and adds the live, floor-level picture it was never built to give you: what each unit actually costs, and which products and customers are earning. You keep what you use today.
Why not just a spreadsheet or a basic ERP?
Because Blitz measures output at the machine and keeps production, cost, stock and profit correct by itself (through product changes, stoppages and shift changes), then brings what needs you to you. That is what lets you quote on today's cost and rank what to run next by what it earns per machine hour. A spreadsheet's numbers are typed: they arrive late, drift wrong and depend on whoever fills them, and they tell you what already happened, when someone finally opens the file.
Is Jarvis an extra?
No. There is one plan, Blitz: machines, production, true cost, inventory, sales and material intake, your whole factory measured and in one place. Jarvis is the part of Blitz that talks to you: it watches what matters and reaches you, answers in plain language and briefs you. See the plan.
How does material intake work?
It's built into Blitz, gate to books: photograph a supplier bill the moment material lands, check and approve it, and clean Tally-ready entries go to your accounts while the stock pool updates. Part of Blitz. No separate app to buy. See how it works.
What can Jarvis do?
Jarvis reads everything Blitz holds, all the time, and brings you the handful of things that need a decision: a machine stopped for longer than the line you set, material about to run short at the rate you are actually consuming it, money overdue past your own terms, an order that will not make its date, a product whose cost per unit has moved against you. You say once what you care about, and after that you stop opening the app to check.
It answers questions too, in plain language, and the span is the unusual part: ask it what machine 12 did last night, or what you are still owed, in the same question box. It is part of Blitz.
What if Jarvis is wrong?
Every figure Jarvis gives you is one you can open on the screen yourself, from the same place your reports come from. If something is missing, Jarvis will not invent it any more than the screen will: you get the blank and the reason.
Where it can be wrong is in what it thought you asked, and you see that straight away, because the answer is about the wrong thing. Ask again in different words and you have lost ten seconds, not a decision.
Does this mean I stop walking my floor?
You walk it for the reason you always meant to: to see the work and talk to the people doing it, not to find things out.
By the time you are on the floor you already know which machines stood and for how long, what ran last night and what it cost. So the 7:40 round stops being a counting exercise and becomes the part that moves something: fixing what you already know is wrong, and deciding what to run next.
And the hours that went into chasing figures go where they earn: quoting new work while the customer is on the phone, and the customers worth more of your time.
What does Blitz cost?
It's designed to pay for itself in weeks, not years. Pricing depends on the number of machines. Book a short demo and we'll quote for the size of your floor. No big cheque upfront, no long contract to sign.
Which factories is Blitz built for?
Any factory that makes the same things in volume on machines. Power looms, narrow fabric and webbing, woven sacks and FIBC, rope and twine, wire and cable, plastics extrusion and auto components are close fits. See the full supported-machines list.
Will it work with my old machines?
Yes. The small sensor is fitted with no rewiring, so age and make don't matter. Old, new or mixed: if a machine runs, Blitz can track it.
How do I use AI in my manufacturing business?
Start where it pays back immediately rather than where the articles start. In a factory of 20 to 50 machines that means three things: letting AI read the purchase orders and supplier bills that arrive as photos and PDFs, so your costing runs on this week's rates instead of last month's; letting it read your own production record back to you, so you can see which customers are growing and which have quietly stopped ordering; and being able to ask questions about the business in plain language instead of building a report. Predictive maintenance and camera-based inspection come much later, and need years of failure data you do not have yet. The full answer is here.
Where do I start with AI in my factory?
Not with the AI. With what it would read. Most small factories record production on a sheet at the end of a shift and key it in days later, so any AI reasoning over those numbers is reasoning over a guess. Measure output off the machine first, then point AI at the paperwork you already handle, then start asking it questions. Done in that order it works from day one; done in reverse it is an expensive way to be wrong faster.
Do I need a data scientist or an IT team to use AI here?
No. You are not training a machine learning model of your own, and there is no server to run. Blitz is hosted and managed for you, and we set it up. The work on your side is fitting a small sensor to machines you already own, which needs no rewiring, no PLC and no integration project. The advice about hiring data scientists and running pilot projects is written for plants a hundred times your size.
Will AI replace my workers?
No. Nothing in Blitz runs a machine or makes a product. Your operators do exactly what they do today. What it removes is the copying: bills retyped into a computer, production figures transcribed off a sheet, reports assembled by hand at the weekend. In practice that gives an office of two or three people their week back, rather than replacing anybody.
Is AI worth it for a factory my size?
Yes, at the jobs that need nothing but your own record. Current rates read off your own bills, a real cost per unit, and a straight answer when you ask which product actually made money last month: those pay back in weeks at any size. The two use cases every article leads with, predictive maintenance and computer-vision quality inspection, need volumes of failure and defect data a small plant will not have for years, which is why AI feels out of reach here. It is not out of reach; it is usually just pointed at the wrong job.
Can AI reduce my manufacturing costs?
Yes, by putting a true cost on each product while you can still act on it. That is usually the first time an owner sees that something he has quoted the same way for years now loses money, and the first time he can say which of his products is worth the machine hour. The saving comes from what you do with that: re-quote it, drop it, or move it to a cheaper machine. What AI will not do is lower your power tariff or your raw material rate by itself, and anyone promising that is selling something.
Still have a question we didn't cover? Ask us on WhatsApp. We'll answer honestly.
Read a little more